0.50mm JIS standard non grain oriented electrical steel

Non grain oriented electrical Steel Coil as one kind of Cold Rolled Steel Coil, as it has high content of silicon, we always call it non grain oriented silicon steel coil.

Product advantage:
1. Due to advanced production lines, equipment and technology, Houming's non grain oriented silicon steel has good magnetic and other properties;
2. No matter the low or high magnetic fields, Houming's electrial steel sheet can keep high permeability over an extensive range;
3. As silicon steel is one kind of Cold Rolled Steel coil, which makes it have good lamination factors.
4. Houming improve the surface coating to meet customers' different appliction, the coating has better insulation, good resistance to heat, oil and rust.
5. Our silicon steel are supplied as strip in coil, it has high dimensional accuracy. It can be supplied slit to any width to facilitate the high speed, high efficiency punching operation of customers.

Product application:
Due to its magnetic properties, the magnetic are same in all dirctions, so non grain oriented silicon steel are very popular in rotating industry like motors, generators, samll tranformers, inductors, magnetic coils, reactors.

What customer need to pay attention when annealing?

Because stress have an adverse effect on the magnetic properties, stress relifef annealing is necessary in order to relife these stress and restore the original magnetic properties.
Here are some precautions for customers when electical Steel Plate are subjected to stree relied annealing.

1. AVOLD EXCESSIVE OXIDIZATION
Oxidization seriously impairs the magnetic properties, particularly at high inductions. In batch-type annealing, excessive oxidization and potential damage caused by impurities present in the annealing atmosphere may be avoided by using an annealing cover, which can be sealed with dry sand. lt is most important for the cover to properly seal off the charge. Any air inside the annealing cover should be flushed out and replaced with a non-oxidizing atmosphere. A non-explosive atmosphere composed of ≤10% hydrogen≥90% nitrogen, or high-purity nitrogen gas are recommended, and the dew point of the atmosphere should be maintained at less than 0℃ (32°F).

2. ANNEALING TEMPERATURE AND HOLIDN TIME
The usual practice of annealing is to raise the temperature of the charge to a level ranging from 720℃ (1,328'F) to 750℃ (1,382F), and to maintain this temperature range long enough to permit uniform heat penetration. Temperature, holding time and atmosphere must be well controlled.

3. COOLING TIME
To avoid distortion of laminations and cores, it is required that the charges should be cooled slowly to a temperature of about 350℃ (662°F) at a rate not exceeding 25C (45* F) per hour, especially for charges weighing only a few tons. For heavier charges, better results will be obtained by a slower rate of cooling.

Specification for non grain oriented silicon steel:

Grade	Thickness mm	Assumed Density (Kg/dm3)	Yield strength				Tensile strength				Elongation %		Hardess	Number of bends
			N/mm2		Ib/in2		N/mm2		Ib/in2		L	C		L	C
			L	C	L	C	L	C	L	C
50A230	0.50	7.60	435	453	63100	65700	557	576	80800	83500	19	20	221	4	5
50A250			407	421	59000	61100	534	552	77400	80100	21	23	213	4	5
50A270			410	424	59500	61500	534	555	77400	80500	22	24	213	4	5
50A290			414	427	60000	61900	534	560	77400	81200	23	25	213	5	5
50A310		7.65	414	427	60000	61900	534	560	77400	81200	23	25	213	12	11
50A350			389	403	56400	58400	529	547	76700	79300	27	28	207	14	13
50A400			332	343	48200	49700	476	494	69000	71600	29	31	184	15 or more	15 or more
50A470		7.70	285	290	41300	42100	423	133	61300	62800	34	35	153	15 or more	15 or more
50A600		7.75	265	268	38400	38900	400	406	5800	58900	34	36	137	15 or more	15 or more
50A700		7.80	276	278	40000	40300	398	402	57700	58300	35	36	127	15 or more	15 or more
50A800			275	276	39900	40000	390	395	56600	57300	36	37	125	15 or more	15 or more
50A1000		7.85	260	262	37700	38000	367	370	53200	53700	37	39	117	15 or more	15 or more
50A1300			256	258	37100	37400	358	360	51900	52200	39	39	112	15 or more	15 or more

Magnetic properties:

Grade	Resistivity	Core loss				Magnetic flux density T
		Watts per kilogram				B10	B25	B50	B100
		50Hz 1.0T	50Hz 1.5T	60Hz 1.0T	60Hz 1.5T
50A230	59	0.95	2.25	1.22	2.93	1.48	1.57	1.66	1.78
50A250	55	1.00	2.40	1.30	3.05	1.49	1.57	1.67	1.79
50A270	55	1.05	2.50	1.35	3.17	1.49	1.57	1.67	1.80
50A290	54	1.08	2.60	1.40	3.25	1.49	1.58	1.67	1.79
50A310	54	1.15	2.70	1.45	3.35	1.49	1.59	1.67	1.79
50A350	51	1.30	3.00	1.64	3.75	1.50	159	1.68	1.80
50A400	47	1.45	3.25	1.85	4.05	1.52	1.61	1.69	1.81
50A470	38	1.65	3.65	2.10	4.65	1.54	1.63	1.71	1.82
50A600	32	2.00	4.50	2.50	5.62	1.52	1.61	1.70	1.81
50A700	28	2.52	5.50	3.30	6.90	1.55	1.665	1.73	1.84
50A800	24	2.95	6.30	3.65	8.00	1.57	1.66	1.74	1.84
50A1000	18	3.25	7.20	4.15	9.15	1.59	1.69	1.75	1.85
50A10300	15	3.75	8.10	4.75	10.20	1.58	1.67	1.76	1.87

Houming's package:

1. Lock buckle                                              2. Belt                                                         3.Metal external protection plate                                  4.Plastic thin film
5. Dedicated air anti-corrosion paper         6. Steel belt                                                7. Metal external angle protection ring                         8. End cover
9. Internal surrounding protection plate    10. Metal internal protection angle ring    11. Paper internal protection angle ring                        12.Paper external protection angle ring

Why you can choose us?
1. As a professional supplier of steel products, we have regular stock of normal standard steel plate, steel coil, Steel Bar, Steel Profile, if you have any interest about steel product, we are gald to provide you quotation.
2. With more than 10 years experience, Houming has technical team work with you to solve your problems.
3. We are gald the third praty to inspect product quality from producing to delivery.